Plastic materials for the industrial sector: which plastic to choose depending on the application

The right plastic is chosen by its use rather than by material family. POM for friction, PA for heavy impacts, ABS for casings, PC or PMMA for glazing, HDPE or PP for tanks, PEEK when heat, chemicals, and sterilization are added. Three traps often recur: stress cracking, wear through heating, and water absorbed by polyamides. The manufacturing process and your sector's standards then narrow down the list.

You have found a material whose technical data sheet seems suitable for your part. However, problems can arise later once the part is in service. A casing cracks after cleaning. A gear jams as soon as the workshop becomes humid. A part goes to an audit without the right certification and comes back rejected. In the end: a stopped line, a run to be remade, sometimes tooling to be reworked.

It is better to settle the material question before launching production. This guide starts from the use rather than the catalog, based on what we see passing through as a processor of industrial plastic parts.

Any doubts about your case? Need advice?


Industrial plastic materials: 3 families to know

Industrial plastic materials fall into three families: standard, engineering, and high-performance. The higher you go, the more the material withstands heat, chemicals, and wear, and the more it costs.

Standard and semi-engineering plastics cover most common needs: ABS, PMMA, PC, HDPE, PP, rigid PVC, PETG, and PS. Their properties-to-price ratio is good.

Engineering plastics are used for parts that move and wear: PA, POM, PET, PVDF, and PEI.

High-performance plastics are reserved for extreme environments: PEEK, PTFE, PPS, PI, and PEKK. They are mostly found in medical, aerospace, defense, and chemical applications.

All these materials are thermoplastics: when heated, they soften; when cooled, they harden. This is what allows them to be thermoformed, bent, or welded.

Criteria that decide the choice of a material

Seven criteria come into play and none is sufficient on its own:

  • Mechanical constraints: impacts, rigidity, flexibility, abrasion.
  • Thermal resistance: operating temperature, hot/cold cycles.
  • Chemical resistance: solvents, oils, acids, bases, cleaning products.
  • Regulatory requirements: food contact, medical compatibility, fire standards.
  • Appearance and finish.
  • Material cost relative to volumes.
  • Compatibility with the manufacturing process.
Our design office cross-references them right from the specifications phase. Two errors often recur: paying for a material that is too premium for a standard use, or selecting a material that falls short and will eventually fail in the field.

Which plastic to choose based on industrial use?

Start with the use, and the material follows. The table provides the starting reflex, and the following sections detail it by sector.
Use Starting material Its advantage Point of vigilance
Friction parts (gears, sliders) POM Keeps its dimensions, slides without grease Strong acids, UV, difficult to glue
Heavy impacts, abrasion PA Absorbs impacts, wear-resistant Absorbs moisture
Casings and covers ABS Impact-resistant, good appearance, easy to thermoform UV, solvents
Protective glazing PC (impacts) or PMMA (optical) Unbreakable or highly clear Stress cracking and scratches (PC), solvents (PMMA)
Tanks, bins, food contact HDPE, PP Chemical inertness, weldable Impossible to glue, limited heat tolerance
Sterilization, medical PEEK, PP, medical PC Withstands sterilization Cost (PEEK)
Highly aggressive chemicals PVDF, PTFE Maximum chemical resistance PFAS regulatory tracking
Heat, fire, defense, aerospace PEEK, PEI, PPS Thermal and fire resistance Cost

Machinery, automation, and friction parts

POM is the first choice for parts that slide, rotate, or snap together: it keeps its dimensions even in humid environments and slides without grease.

Gears, bushings, cams, rollers, sliders: all these are made of POM. If impacts are heavy or abrasion severe, PA handles it better.

Around these parts, casings are made of ABS, inspection windows of PC, and light wear parts and guides of HDPE. We machine them using 3 and 5-axis CNC, with the tight tolerances demanded by the industrial sector.

Medical and laboratory

PEEK is essential whenever a medical part must survive repeated sterilization while remaining biocompatible.

For housings, incubators, and transparent tanks, medical-grade PC combines transparency and impact resistance. PP withstands steam sterilization, making it suitable for laboratory trays, bins, and tanks.

Medical-grade POM-C is used for dosing blocks. In all cases, ask for the certified grade, not just the material name. This is the rule we apply for the medical and healthcare sector.

Food industry

HDPE is the staple material for the food industry: non-porous, washable, and available in a certified food grade.

It withstands knives and frequent washing and is therefore recommended for cutting boards, transfer bins, and conveyor guides. Food-grade POM-C equips distribution star wheels and scrapers.

If acidic and basic cleanings are severe, PVDF takes over for fluid circuits. Discover our projects for the food industry sector.

Transport, mobility, and railways

For vehicle interior trimming, ABS remains the common choice: lightweight, impact-resistant, and with a good surface finish.

In railways, the EN 45545 standard changes everything: a standard grade is not automatically accepted. A certified flame-retardant formulation is required for the specific area.

For special vehicle fairings, polyurethane RIM injection is an option. Our thermoforming vs. injection comparison helps you decide. See also the automotive and transport sector.

Aerospace, defense, energy, and chemicals

PEEK, PEI, and PPS are the benchmarks when heat, fire, and chemicals combine, particularly in aerospace and defense.

For canopies, domes, and glazing, PMMA provides clarity and UV resistance, while PC offers impact resistance. We form them through contactless blowing, which preserves optical quality.

In chemicals and energy, welded HDPE and PP are used for tanks and retention basins. PVDF and PTFE handle highly aggressive fluids. This is the realm of plastic boilermaking, especially for the energy and environment sector.

Is your use case not on this list, or are you hesitating between two materials?

The 3 traps that cause material choice failures

Three traps recur when a material choice goes wrong. They are discovered in service, rarely upon delivery.

Trap 1: stress cracking, or the casing that breaks without impact

An amorphous plastic under tension can crack cleanly upon contact with an oil or solvent, without any impact. PC, ABS, and PMMA are the most exposed.

The scenario is classic: a polycarbonate machine-tool window, cleaning with the wrong product, and a crack starting from a sharp corner.

To mitigate this, it is better to use the right cleaning product, have rounded internal corners, and use a stress-relieved part after machining. For PMMA, warm soapy water is sufficient for cleaning. Semi-crystalline materials (HDPE, POM, PA) tolerate solvents better.

Trap 2: wear through heating

In friction applications, the material's resistance matters less than its ability to handle the heat of sliding.

Plastic conducts heat poorly: it accumulates at the interface, the surface softens, and the part deforms.

Pure PTFE slides very well but deforms under pressure. If some space is not left around this PA part, it will swell with heat and moisture, eventually jamming the mechanism. Two solutions: a POM, or a grade filled with solid lubricant (PTFE, graphite) that reduces friction and extends lifespan.

Trap 3: water absorbed by polyamide

A polyamide swells and softens in a humid environment, whereas a POM retains its dimensions.

PA absorbs moisture from the air: the part changes dimensions and loses rigidity. A precisely fitted gear in a dry workshop will jam when production shifts to a humid environment.

For tight tolerances or humid environments, POM is clearly superior. For heavy impacts, PA remains better, provided clearance is factored in.
A part that cracks, wears out too quickly, or jams in service? Have your case analyzed by our design office. And if the original part no longer has a blueprint, reverse engineering and 3D scanning allow it to be remade, with a better material if necessary.

The material also depends on the manufacturing process

Not all materials thermoform, glue, or machine equally well. The process narrows down the list before even discussing cost.
Process Common materials
Thermoforming ABS, ABS/PMMA, ABS/PC, HDPE, PP, rigid PVC, PETG, PC, PMMA
CNC machining POM, PA, PEEK, PTFE, HDPE, PMMA, PC, ABS, PVC
Boilermaking and welding HDPE, PP, rigid PVC
Bending and hot folding PMMA, PC, PETG, ABS, rigid PVC
RIM injection Polyurethane
Extrusion blow molding HDPE, PP, LDPE (hollow bodies); PMMA, PC (contactless blowing)

HDPE and PP cannot be glued: they are welded. POM cannot be thermoformed: it is machined.

Choosing the material before the process sometimes forces a redesign of the part. It is better to decide on both together with our design office.

Prototype, single part, or small run? Send us your blueprints: we validate the material and the process before committing to tooling.

See our offering for custom plastic parts manufacturing


Certifications and standards: what your sector requires

Your sector often dictates the material before your technical preferences.

  • Railways: EN 45545 standard (fire and smoke).
  • Medical and pharmaceutical: USP Class VI and ISO 10993.
  • Food industry: food grade (FDA, European Regulation 10/2011).
  • Aerospace and industry: UL94 V0, FAR 25.
  • All sectors: REACH and RoHS.
A standard is verified on the exact grade, not on the material name: always ask for the certificate.

Upon request, we provide 2.1 and 3.1 material certificates and batch traceability, backed by our quality control and our quality approach and certifications.

PFAS: PTFE and PVDF under European surveillance

If you specify PTFE or PVDF for a long-lasting project, keep an eye on the ECHA PFAS dossier. The restriction proposal targets all PFAS, including fluoropolymers.

The Risk Assessment Committee adopted its final opinion in early March 2026. The Socio-Economic Analysis Committee adopted its draft opinion shortly after, with a public consultation open until May 25, 2026.

Its final opinion is expected by the end of 2026. ECHA will then forward it to the European Commission, which will prepare a proposal submitted to a vote by the Member States. As of late October 2026, no final restriction has been adopted.

Right from the specifications phase, ask if the part will still be produced in several years. If so, compare with an alternative and secure a stock.

Need a material certificate, a certified grade, or an opinion on a standard?

Choosing your material with Plastisart

At Plastisart, the material is chosen during the study phase. Our design office cross-references use, process, standards, and budget right from the specifications.

It then validates the material with the technicians who will transform it in our workshops and with our machines. We keep common materials in stock (ABS, PMMA, PC, HDPE, PP, PVC, POM, PA), which avoids supply delays for urgent requests. A single point of contact follows the part, from material to delivery.

Plastic materials for the industrial sector: your questions on material selection

What are the main industrial plastic materials?

They are classified into three families. Standards (ABS, PMMA, PC, HDPE, PP, PVC) cover common needs, engineering plastics (PA, POM, PET, PVDF, PEI) serve moving parts, and high-performance plastics (PEEK, PTFE, PPS, PI, PEKK) are aimed at extreme environments.

Which plastic to choose for a part subject to friction?

POM, for its dry sliding and dimensional stability. If impacts are heavy, PA is more resilient: allow clearance for moisture. A grade filled with solid lubricant extends lifespan.

Which plastic to choose for food contact?

HDPE, PP, or POM-C, in a certified food grade. Ask for the grade certificate, not just the material name.

How to know if a plastic resists a chemical product?

Semi-crystalline materials (HDPE, PP, POM) withstand solvents better than amorphous ones (PC, ABS, PMMA). The only reliable test remains testing with the actual product on a part under stress. Our design office can help you frame it.

Can a metal part be replaced by an engineering plastic?

Often yes, for friction, protection, and casing parts, provided the load and operating temperature are verified. Our article on industrial parts made of plastic materials details the advantages over metal, and our design office validates feasibility on a case-by-case basis.
Another question on material choice? Write to us, we will answer you.

Technical mastery

Integrated design office

Complete service from design to completion

Small and large series

Custom manufacturing

A unique experience

We are committed to offering you secure and customizable browsing. We use cookies for this purpose to provide you with offers tailored to your areas of interest, anonymously collect statistical data and make your visit as pleasant as possible.